<sub id="b7dt9"><dl id="b7dt9"><big id="b7dt9"></big></dl></sub>
        <nobr id="b7dt9"></nobr>

        <meter id="b7dt9"></meter>

        車輪裝備 車輪模具 汽車模具 汽車零部件 車橋

        端徑跳在線檢測儀

        端徑跳在線檢測儀

        該設備可實現車輪輪輞端向和徑向的跳動檢測,為滿足檢測節拍要求,夾緊機構、頂升機構、壓緊機構均采用氣動執行元件,從而實現了汽車輪輞的快速夾緊與定位。

        This equipment can realize test for radical run-out and axial run-out of wheel rim. To satisfy requirement to test tact, the clamping device, jacking device and pressing device all use pneumatic actuator, which can clamp and locate rim quickly.

        詳細描述

        概述

        Summary

        該設備可實現車輪輪輞端向和徑向的跳動檢測,為滿足檢測節拍要求,夾緊機構、頂升機構、壓緊機構均采用氣動執行元件,從而實現了汽車輪輞的快速夾緊與定位。

        This equipment can realize test for radical run-out and axial run-out of wheel rim. To satisfy requirement to test tact, the clamping device, jacking device and pressing device all use pneumatic actuator, which can clamp and locate rim quickly.


        工件從上一工序到達本工序,傳送到預定位置,檢測開關檢測到工件,夾緊機構將工件送到檢測位置下方,頂升夾緊機構將工件頂起并夾緊定位,壓緊機構將工件壓緊,伺服電機旋轉帶動工件旋轉,檢測機構檢測工件,檢測完畢后合格產品通過傳送機構傳送到下一工序,對于不合格產品可通過后面的分選機構分選。

        The workpiece from last process of fitting-press machine to this process will be conveyed to the appointed position, workpiece will be detected by detecting switch and will be conveyed below detection position by clamping device. The jacking device will jack workpiece up, clamp it and locate. Pressing device will press the workpiece. Servo motor rotates to drive workpiece rotation. The testing device will test workpiece. After test the qualified product will be conveyed to next process by transmission device, and the unqualified one will be selected out by the selecting mechanism.


        該設備實現了過程的自動化與檢測數據的可視化,達到穩定產量、提高質量、降低消耗、高效實用的目的。

        This equipment realizes automatically production process and visual testing data. It achieved target of constant production, quality improvement, consumption reduction and high efficiency and pragmatic function.


        規格參數

        Specification

        設備型號

        Model Number

        JCJ13-18AH

        電網電壓

        Power Supply

        AC 380V, 3phase, 50Hz

        輪輞最大寬度

        Rim Max. Width

        290mm

        輪輞最小寬度

        Rim Mini. Width

        120mm

        壓縮空氣

        Compressed Air Pressure

        0.4~0.6Mpa

        輪輞最小直徑

        Rim Mini. Diameter

        12 inches

        輪輞最大直徑

        Rim Max. Diameter

        18 inches

        中心孔定位精度

        Position Accuracy of Centre Hole

        0.03mm

        主軸自身徑跳精度

        Radial Runout Accuracy of Spindle

        0.03mm

        設備結構簡介

        Equipment Structure Introduction

        該設備包括控制系統、上料系統、檢測系統和分選系統四大部分;主要由1傳送機構、2夾緊機構、3頂升旋轉機構、4壓緊機構、5檢測裝置、6分選機構等組成;

        This equipment can be divided into four parts: control system, feeding system, testing system and selecting system. It mainly consists of transmission device (1), clamping device (2), jacking-rotating device (3), pressing device (4), testing device (5), selecting device (6), etc., shown as below pictures.

        可實現自動送料機構同生產線連接,該設備能自動將工件輸送到預定工位,夾緊機構夾緊工件并輸送到檢測區,頂升機構定位找正并將工件抬起、壓緊機構將工件壓緊、頂升旋轉機構帶動工件旋轉,檢測裝置在線檢測。

        Its automatically feeding device can be connected with production line. This equipment can convey workpiece to the appointed processing position automatically. Clamping device grips workpiece and conveys it to testing part. Jacking device locates and lifts workpiece up. Pressing device presses workpiece, jacking-rotating drives workpiece to rotate and testing device will do the online testing operation.


        ? 2018 山東小鴨精工機械有限公司 版權所有|魯ICP備11005049號-1


        歡迎掃碼咨詢合作

        地址:山東省濟南市工業南路51號

        營銷事業部:+0531-83122188

        郵箱:xiaoyatooling@163.com

        400-6586-222轉8

        欧美一区二区精品蝌蚪91-日韩亚洲欧美精品-亚洲精品专区无码在线-亚洲成人网站网址在线免费观看

          <sub id="b7dt9"><dl id="b7dt9"><big id="b7dt9"></big></dl></sub>
              <nobr id="b7dt9"></nobr>

              <meter id="b7dt9"></meter>